|
SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> The Marketplace >> Lancer's Performance Parts /cgi-bin/YaBB.pl?num=1338581006 Message started by LANCER on 06/01/12 at 13:03:25 |
|
Title: Lancer's Performance Parts Post by LANCER on 06/01/12 at 13:03:25 JETSET (http://suzukisavage.com/cgi-bin/YaBB.pl?num=1336741909) Performance Carburetor Kit (http://suzukisavage.com/cgi-bin/YaBB.pl?num=1338654578) Performance Camshaft: Stage 3 (http://suzukisavage.com/cgi-bin/YaBB.pl?num=1338603955/0#0) Wiseco Pistons (http://suzukisavage.com/cgi-bin/YaBB.pl?num=1436923466) http://www.savageriders.com/verslagen/CamChainClub/verslavy.jpg [size=24] http://savagebeastperformanceparts.com -Performance Camshaft: ... Stage 3 is the profile available, which is a combo of 1&2 with the duration of Stage 1 and the higher lift of Stage 2. The machine work is done by Webcam Inc. which does a Hard Weld cam lobe surface, in business for over 60 years. **Your cam core in exchange is required to make the Performance Camshafts. ($100 core charge otherwise) Shipping cost is included in the price. ($329 ebay/$299 here) -Performance Carburetor Kit: ... Includes 36mm Mikuni VM Performance Carburetor; custom throttle cable by Barnett; new rubber mounting flange; Sudco/Mikuni Carburetor Manual (lots of info on carb theory, tuning, jetting, exploded parts views and part numbers, etc...a virtual carb course); Jet Pak with 4-5 extra pilot jets and 9-10 extra main jets; Mikuni carb tool kit, spark plug. ($439 ebay/$399 here) -Wiseco Pistons: ... 94mm (out of stock), 95mm, 96mm & 97mm. Forged aluminum, 10.5:1 compression ratio vs. 8.5:1 for stock piston. $229 ebay/$199 here. -Reworked Cylinder Head:... Hand lapping of valves (includes new valve stem seals) & intake/exhaust porting to maximize air flow to increase power and efficiency. The head is blasted on the outside and inside the ports as well. $250 If you purchase a head from me ( if available ) then that cost is separate and will be determined based upon the condition of the head. (camshaft is purchased separately) **Higher milage engines often require new or reworked rockers. Rockers can be Hard Welded by Webcam if additional durability is desired. Heavy duty racing valve springs kit with titanium keepers is also available. -Standard Rocker set ($110) -Hard welded rockers ($240) … hard welding only; your usable old rockers required, or purchase of new rockers. -Race valve spring kit ($250) … not recommended for street use.performance dual springs, Titanium retainers, shims. -Custom front brake line & throttle/clutch cables. Price varies based on length needed and type of sheath desired. Sheaths can be Black Vinyl, clear coat Stainless Braid. They are made to my specifications by Barnett to match the 3 model year LS650 type of throttle connections and stock or Performance Carburetor used. Contact with spec's desired for a cost estimate. $250 for full set. -Heavy Duty Barnett Clutch Pak Set (Friction disc set + springs ) ($125) -Kevlar Front/Rear Brake Set ($85) -Nitrided Camshaft chain ($89) -Cam chain guide set ($120) -Cam chain adjuster assembly ($75 ) with bolt & clip -Complete Gasket Set ($125) -JETSET ($39.95 ebay/$29.95 here) … #50, 52.5 & 55 pilot jets; #150, 152.5 & 155 main jets; 3 washers to replace the white plastic spacer on the needle; float bowl gasket. Any single or combination of the above Performance Parts will improve efficiency and power, but a better flowing exhaust system is a key factor in maximizing efficiency and performance. A stock LS650 engine makes 30hp at the crank and 25hp at the rear wheel. Expect about 40+hp at the rear wheel with the above improvements, along with a good flowing exhaust system. The transformation of the bike is dramatic … it is a totally different animal. |
|
Title: Re: Lancer's Performance Parts Post by dirtydom on 06/27/12 at 20:01:36 ordered a jet set from you a couple of days ago. thanks. :) |
|
Title: Re: Lancer's Performance Parts Post by Bosgarage57 on 07/03/12 at 06:21:00 Are you still making the Hard Krome exhausts? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/03/12 at 15:54:20 4A677B6F697A696F6D3D3F080 wrote:
I don't make them but I do have a couple sitting around |
|
Title: Re: Lancer's Performance Parts Post by Bosgarage57 on 07/03/12 at 16:00:06 can you get me a price? Possibly a sound bite? Wondering if I should go with yours or try to call my local HD and do the dyna route. I want it to be loud, straight pipe ish loud, but dont want to hurt the engine. I know I'll have to buy some needles from ya too :) |
|
Title: Re: Lancer's Performance Parts Post by heroicseven on 07/03/12 at 18:16:22 that sounds good to me too :) |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/04/12 at 04:48:32 I will get a pic of the muffler/s today and post them. I do not have a video with sound of them, but it seems that one may have been posted a few years back ... but the memory is very fuzzy on that. The Hard Krome mufflers are a loud muffler and do have removable steel spiral baffles, but they are loud enough that removal is not needed. Besides, the engine needs the back pressure created by the baffles. Found some older pics of the muffler 3 sizes: I have one each of the middle and larger sizes http://images1.snapfish.com/232323232%7Ffp342%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32336%3A54%3C68%3A4nu0mrj end view of spiral baffles http://images1.snapfish.com/232323232%7Ffp33%3B%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32336%3A555%3B724nu0mrj side cut-a-way view of baffle system http://images1.snapfish.com/232323232%7Ffp339%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32336%3A554935%3Anu0mrj I have one of the bottom of the two shown so it would need to be cut to fit your needs http://images2.snapfish.com/232323232%7Ffp533%3A5%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32386%3B4%3A4%3B487nu0mrj this is a pic of the smallest version mounted on my Savage some years ago http://images1.snapfish.com/232323232%7Ffp346%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32336%3A555%3B758nu0mrj |
|
Title: Re: Lancer's Performance Parts Post by Bosgarage57 on 07/04/12 at 06:49:01 thank you lancer, I really like the small one you had on your bike. Seems to flow well with the lines of the bike. What would be the price on the larger one, and the one in the middle? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/04/12 at 09:46:22 6E435F4B4D5E4D4B49191B2C0 wrote:
I got these a few years ago but they are new & never used. Retail was in the $350/pr range. Hard Krome's guarantee said they would never discolor. I will go $75 + shp. That's the price range of Emgo's longer mufflers and these a waaaay better quality. I've kept them to use myself but will be moving next year to Oklahoma so am letting some things go. I won't likely sell all of them so it's sort a 1 at a time thing for now. |
|
Title: Re: Lancer's Performance Parts Post by Bosgarage57 on 07/04/12 at 13:07:38 I'll gladly take a set. The medium if you dont have any small ones. I'll also need a jet set. If you'll accept PayPal I can send it as a gift today. Thanks! |
|
Title: Re: Lancer's Performance Parts Post by Fl jay on 07/04/12 at 17:38:20 Lancer did you get the order. My wife sent. Frome Janet. Avallone we've already sent your payment to PayPal if you did receive the order please e-mail me at jayavallone@gmail.com. It has been several weeks. Thanks Jay :'( |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/05/12 at 02:58:45 757E767C707F232225110 wrote:
Yes, I have the order. Was out of some jets prior to the Dragon ride and was holding back waiting for them but they did not arrive until after I left for the ride. I'm working through the back orders now so you should have them in a few days. Sorry for the delay and not getting a msg to you about it. |
|
Title: Re: Lancer's Performance Parts Post by rfw2003 on 07/05/12 at 18:14:21 What part of OK you moving to Lancer? I'm in NE TX |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/06/12 at 02:28:26 4D59480D0F0F0C3F0 wrote:
Henryetta; 75 east of OKC on I-40 and about 70-75 due south of Tulsa Indian Nation Turnpike comes out of Henryetta heading south |
|
Title: Re: Lancer's Performance Parts Post by rfw2003 on 07/06/12 at 02:30:53 I know exactly where that is, about 3 hours from me. R.F. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/06/12 at 03:33:48 75617035373734070 wrote:
You are up early :) I will be building on some acres on the N. Canadian River about 15 miles outside of town |
|
Title: Re: Lancer's Performance Parts Post by rfw2003 on 07/06/12 at 05:23:22 4B46494442551510270 wrote:
Up early no, Just haven't been to sleep yet. I have a terminal case of insomnia. There are times I go days without any sleep at all :( Sounds really nice. Wish I had a few acres. I do have a fairly decent sized spot, but do wish it were bigger. it's about 200ft x 300ft R.F. |
|
Title: Re: Lancer's Performance Parts Post by dirtydom on 07/06/12 at 14:22:03 hey lancer, ordered some jets from you a couple of weeks ago and curious on the status. thanks. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/07/12 at 04:58:11 7B766D6B667B70721F0 wrote:
will have them ready to go this weekend; playing catch up after being gone |
|
Title: Re: Lancer's Performance Parts Post by 96BOB on 07/21/12 at 17:41:17 hey lancer any chance on getting some extended cables? i asked in another post but apparently didnt post it in the right place? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/25/12 at 05:05:31 0906727F72300 wrote:
email me @ savage.s40@gmail.com |
|
Title: Re: Lancer's Performance Parts Post by TROX on 09/15/12 at 08:26:25 Hey Lancer, I was wanting to get a jetset, I PM'd you, but I wasn't sure if your PM's were working so I thought I'd post it as well. Can you let me know if you're still selling them ? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/15/12 at 11:08:39 696F72653D0 wrote:
Yes I am. You can Paypal the $20 to the email address at the post up above. If you want a float bowl gasket then add $3 to it. |
|
Title: Re: Lancer's Performance Parts Post by mikey2004 on 01/07/13 at 18:56:19 I know the last post on it was back in july but by chance do you still have the mufflers? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 01/14/13 at 02:44:54 7470727C602B29292D190 wrote:
I almost lost you; forgot where you had posted this question. YES, if you are referring to the Hard Chrome mufflers. I have 2 small and one large with an extended pipe on it which can be cut to size, depending on how someone may wish to mount it. I will sell these for $40 + shp, each. |
|
Title: Re: Lancer's Performance Parts Post by mikey2004 on 01/14/13 at 05:21:05 I would love to buy one of the smaller ones. Can you tell me how much it would be with shipping to Sarasota Florida and an address to send a check to.? I can use pay pal if you wish. Just need to know how to access you on there. Thank you |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 01/15/13 at 08:40:52 7773717F63282A2A2E1A0 wrote:
Figure $20 for shipping (the boxes I have for mufflers are USPS Priority) Paypal to savage.s40@gmail.com *make not what the payment is for please |
|
Title: Re: Lancer's Performance Parts Post by mikey2004 on 01/15/13 at 17:31:19 ok let me get the money together. i will be in contact, thank you. |
|
Title: Re: Lancer's Performance Parts Post by trini tuner on 02/21/13 at 08:02:56 Hey Lancer, I sent you a pm regarding a JETSET, i dont see the message in my outbox so just makin sure you got it. Thank you |
|
Title: Re: Lancer's Performance Parts Post by HJH on 02/21/13 at 10:57:31 I presume there was one performance carburetor kit and it is now gone? Comes under the heading of you snooze you lose. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 02/22/13 at 03:55:50 5351531B0 wrote:
I have one but it MAY be taken already; got an email yesterday so he has first call on it. It he does not take it then you will be next in line for it. My move to Oklahoma is close at hand so after this one it may be a month or two before I can devote time to bike parts again. |
|
Title: Re: Lancer's Performance Parts Post by HJH on 02/22/13 at 12:19:39 If the other guy takes this one, consider me next in line, whenever you get around to it. If he backs out, I'll take the one you've got. |
|
Title: Re: Lancer's Performance Parts Post by HJH on 03/09/13 at 13:13:40 Just bought the carb off eBay, I think. I'd really like it with the Dial-a-Jet and UFO installed, as per the info on eBay, even if I have to wait until after your move. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/11/13 at 01:48:02 5A585A120 wrote:
Woke really freaking early with head/neck pain ... pretty much part of my daily life so just have to roll with it ... but just saw your ebay/paypal purchase verification on the carb kit. I can add the UFO and Dial-a-jet but as noted before it will take a some time. I am on the road on the way to Oklahoma and in a motel now, with 2 more days to go. I am not sure exactly when I can put the carb together for you. My guess right now is that it may take several weeks before I can get to it. I have the carb and I think I have a spare UFO on hand, but will need to order the DAJ. The UFO & DAJ are $35 & $75 with $10 shp. ** I also need to know the model year of your bike so the correct throttle cable is included. Go ahead and process the Paypal for the UFO & DAJ and I can call right away and get the DAJ ordered so I have it on hand when I'm able to put the kit together. |
|
Title: Re: Lancer's Performance Parts Post by HJH on 03/11/13 at 13:29:43 Thought I included the year of the bike in the comments - 2002. The UFO and Dial-a-jet didn't show up as something you're selling when I was buying the carb, but I'll give it a try. Get around to it when you can. |
|
Title: Re: Lancer's Performance Parts Post by HJH on 03/11/13 at 13:54:39 Payment for UFO and Dial-a-Jet sent. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/18/13 at 11:56:05 181A18500 wrote:
Arrived in OK, unloaded, resting and doing admin stuff for OK. Should be able to get some time for bike stuff on a few days this next week. |
|
Title: Re: Lancer's Performance Parts Post by Liffey3 on 04/08/13 at 09:55:32 Hi Lancer, I would like to purchase a round slide carb with a Dial a jet and UFO as well as a performance CAM. Can you let me know price and stock? Thank you! |
|
Title: Re: Lancer's Performance Parts Post by JPSBOBBER on 04/09/13 at 16:11:55 Hi Lancer, Could you get me a price for an extended throttle cable for a 1999 savage, but fitted with 10" ape hangers ? Thanks ! |
|
Title: Re: Lancer's Performance Parts Post by Liffey3 on 04/09/13 at 19:58:18 Hi lancer, I sent an email regarding your reply. Since I have not posted ten times, I could not reply vie the forum message. By the way, I forgot to mention my bike is a 2006 regarding the cables you mentioned. Thank You! |
|
Title: Re: Lancer's Performance Parts Post by harperlogan007 on 04/13/13 at 07:55:04 Do you have any more of the hard chrome mufflers? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 04/13/13 at 14:53:35 323B282A3F2836353D3B346A6A6D5A0 wrote:
Yes, I do. I even think I can find them among all the other boxes. It helps that the muffler boxes are long and triangular. :) I have 1 small and 1 large, and the large one has an extended section of pipe 2-3' long on the front end. I may have a photo somewhere but if not I will take another. $50 + shp. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 04/13/13 at 15:03:59 63797A6B666B6B6C7B290 wrote:
It is best to put the bars on the bike and run a small flexible wire or chord from the throttle control on the bar down to the carb, following the exact route you want the cable to take. When you have done that and marked the wire/chord where you want the end point to be, then take it off and stretch it out straight on a table or the floor and then measure it from end to end to within 1/2". That is the length you will tell me to make the cable sheath. This is the best way to avoid a TOO LONG or TOO SHORT cable. They cost too much and take to long to get to risk getting it wrong. Not sure about price just yet. I am working through a new source here in OK now, but should know something within a week. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 04/13/13 at 15:12:12 7563696A72746F060 wrote:
Carb kit: $369 DAJ: $80 UFO: $40 Cam: $239+$50 core charge if you do not send your core at the beginning. Core charge refunded as soon as your old core gets to me. I have the carb but need jets & throttle cables for the '95-04 models. I have some cables for the other model years. Cables can take 2-3 weeks to get at times. DAJ & UFO need to be ordered but are quick to arrive. Camshafts take several weeks to get back from Webcam. |
|
Title: Re: Lancer's Performance Parts Post by Liffey3 on 04/16/13 at 12:02:35 Hi Lancer, I have been experiencing email issues. Can you email me at liffey3 at gmail.com? I will pay for the Carb, DAJ, UFO and CAM. My Bike is a 2006. I am doing a 17/43 chain conversion and am a little heavy on the throttle, so whatever CAM will help make up the low end loss I will have with the chain conversion is the one I think I should go for. Number 2 or 3? I do not have the bike apart right now so I do not have a CAM to send. Do you have one to send initially? I am ready to go as the bike is being broke down the end of this week to get painting, new tank, wiring fixes etc. I can pay by paypal when you want. Thank you, Jason |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 04/16/13 at 19:23:54 70666C6F77716A030 wrote:
Sent you a long email. |
|
Title: Re: Lancer's Performance Parts Post by Jacob on 04/18/13 at 16:22:31 Hey, I seen you had two hard chrome mufflers left. One small and one big. Is the small one a direct fit? How much do you want for it? I purchased a jet kit from you last year and now need a 50 pilot jet and also need the TEV spring. Can you hook me up? |
|
Title: Re: Lancer's Performance Parts Post by Jacob on 04/19/13 at 14:53:57 I was able to find and buy a new TEV spring but still in need of the 50 pilot jet and info on the hard chrome muffler.. Thanks |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 04/19/13 at 18:08:05 416A6864696064796F6E780B0 wrote:
The muffler has a 1 3/4" ID which is slightly larger than a stock muffler. Most folks just cut the center out of a soda can and wrap it around the end of the header a time or two, push the new muffler on and clamp it down. The thin aluminum takes up the extra space and "crushes" down quite well and makes a very good exhaust seal. If you ever take the muffler off to do something, I would use fresh aluminum when you put the muffler back to get a good fresh seal. It is as good as most anything else and costs nothing to do it.The muffler is $50 + shp and I will toss the pilot jet in. |
|
Title: Re: Lancer's Performance Parts Post by thecoolerking on 07/11/13 at 07:46:48 I'm a new S40 owner and net to the forum so I can't PM yet, but I'd like to order a jet kit. Could you PM me? I know Henryetta. Home of Troy Aikman (at least his HS playing days). Been through there a lot. |
|
Title: Re: Lancer's Performance Parts Post by thecoolerking on 07/22/13 at 08:58:01 Thanks Lancer, I got your IM. Sent the paypal payment your way. |
|
Title: Re: Lancer's Performance Parts Post by Stealthmobile on 07/29/13 at 13:11:21 so much to do and buy, so little time and money!! hi i'll be bugging you about various things, up to and including carb kits, cams, and big bore kits. I hope that I don't drive you nuts with questions and such! |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/29/13 at 18:10:36 6F4A5D4E634A595B4E592B0 wrote:
No problem dude, the "Nuts" set in years ago so it just feels normal now. ;D |
|
Title: Re: Lancer's Performance Parts Post by dirty dog on 09/21/13 at 16:38:25 hay lancer are still selling jet kits. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/22/13 at 03:43:34 6568737578656E66210 wrote:
Yes, though currently out of some sizes which are on back order. It could be weeks before they are available. |
|
Title: Re: Lancer's Performance Parts Post by rob662ca on 10/07/13 at 09:13:46 hi, do you still sell the jetset? would you ship to canada? |
|
Title: Re: Lancer's Performance Parts Post by rxthumper on 10/21/13 at 22:30:36 do have any timing chains, if so how much? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 10/22/13 at 03:51:36 7278616C6C3639000 wrote:
I don not have chains on hand. Bikebandit.com is a good source if you need it quickly. |
|
Title: Re: Lancer's Performance Parts Post by aegerprimo on 10/22/13 at 18:31:42 Lancer, do you have any dyna or other slip-on upgrade that you'd be willing to sell? I ordered a dyna off fleabay and they sent me one with holy baffles. Been told not to spend the money on trying to use it and to buy another but can't find none for less than 60 bucks. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 10/23/13 at 05:47:22 717E7B777575100 wrote:
I have a couple of spare mufflers but they are not Dyna's. One is a "trumpet" style from Apollo Cone; all stainless inside and out and chrome plated. I used it for a while on my stock S40 but it was louder than I wanted so put a dyna back on. I has a 1 3/4" straight through core with spiral baffling around that. It will flow a lot of air. They are $135 new and are a quality unit. I will sell it for $75 + shp in you have interest in it. I also have a Hard Krome muffler, and it is also a stainless unit with chrome plating. It too has a straight through core with spiral baffling so the sound level and air flow will be similar to the Apollo Cone. It is new, was made for Harley's and sold for $350-375/pr retail. I've had this for a while but never used it. $75 + shp for this one as well. It is the larger of the 3 shown; all are Hard Krome mufflers http://images1.snapfish.com/232323232%7Ffp342%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32336%3A54%3C68%3A4nu0mrj http://images1.snapfish.com/232323232%7Ffp346%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32336%3A555%3B766nu0mrj This is the trumpet style http://images1.snapfish.com/232323232%7Ffp%3B%3B8%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D35%3A86438%3B%3B339nu0mrj |
|
Title: Re: Lancer's Performance Parts Post by aegerprimo on 10/23/13 at 07:47:48 Ate you in agreement with others that my stock 97 savage will run like Crap, if at all, with the racing baffle or what Serowbot called Holy Tubes? Also, shipping to GA, how much? |
|
Title: Re: Lancer's Performance Parts Post by WD on 10/23/13 at 09:29:28 My stone stock less the OPEN straight pipe 1998 ran fine. Just a bit lean (75-85 mpg lean). Your new jets are on the way. Expect a massive drop in fuel economy (like 10 mpg less if you have stock buckhorns, in HALF if you have apehangers). The Mikuni BS40 has got to be the worst piece of junk that J.A. Pan Inc ever installed on a mid-sized bike... It's an 883 Sporty upgrade. >:( |
|
Title: Re: Lancer's Performance Parts Post by aegerprimo on 10/23/13 at 10:43:33 Really? What is that all about? Handlebars affect fuel economy? |
|
Title: Re: Lancer's Performance Parts Post by WD on 10/23/13 at 10:50:41 Ever gone sailing? Same principle, the higher the bars, the more surface area to catch the wind. On a bike, it induces drag, using more fuel to achieve speeds. |
|
Title: Re: Lancer's Performance Parts Post by aegerprimo on 10/23/13 at 10:56:20 Funny you say that cuz I can't stand those buckhorn. |
|
Title: Re: Lancer's Performance Parts Post by Steddy58 on 12/25/13 at 12:59:13 How much to ship the carb to the UK and would it go straight into my 1988 sav with the raptor petcock,cheers Steph |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 12/26/13 at 03:42:17 436475607854100 wrote:
Looks like it will be in the $50-60 range plus insurance. I could not get a specific price without having your postal code. |
|
Title: Re: Lancer's Performance Parts Post by Steddy58 on 12/30/13 at 03:05:26 Postal code ch1 3hd, its mainland UK,cheers |
|
Title: Re: Lancer's Performance Parts Post by Klobchar on 01/02/14 at 17:22:49 Mr. Lancer, please e-mail me or PM. Apparently my nuts haven't dropped far enough to send private messages yet. I guess I will need to work on that. Anyways, in regaurds to what you may be able to help me with. I need several pieces for my machine (95 savage). Doing a total rebuild. maybe even a new carb. PO must of snorted meth off the screwdriver before raped the brass...on EVERY god-foresaken screw! ugh... :-[ |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 01/03/14 at 02:53:59 If you have not seen it before, this is from the "Marketplace" and is the listing for the primary items offered. http://suzukisavage.com/cgi-bin/YaBB.pl?num=1338581006 |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/02/14 at 11:30:48 I too am interested in the small pipes, and would need jet set for my 2012 savage. I need louder pipes I am tired of almost getting run off the road because people don't hear me coming. Do you still have the small pipes available? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/03/14 at 06:53:56 606C7A6C61617E3F3F3C3E0D0 wrote:
Will need to check on the pipes. If the roads are good I can do that tomorrow; I have most of my parts stored at another location. |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/05/14 at 08:57:28 Did you get a chance to look for the pipes Lancer? I hope you still have one, I will want to purchase a jetset along with it. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/05/14 at 09:23:43 464A5C4A47475819191A182B0 wrote:
YES, I have 2 of the Hard Krome mufflers. $60 + shp |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/05/14 at 09:34:23 great I will take one and a jetset please e-mail me as I cannot yet send pm's mawalls2213@gmail.com thank you Lancer. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/06/14 at 02:02:04 737F697F72726D2C2C2F2D1E0 wrote:
Can you Paypal or do you need an invoice for credit/debit or want to use a MO ? |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/07/14 at 12:28:57 Invoice would be best, I don't have a pay pal, If it's not too much trouble.I emailed you yesterday I think. |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/15/14 at 10:14:47 I got the Muffler thanks Lancer, nice touch with the confetti it was like Christmas morning ;D |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/15/14 at 17:24:29 2824322429293677777476450 wrote:
LOL ... yep, my wife just loves it when I transfer the paper from the shredder to the boxes ... the stuff goes everywhere and she has to vacuum all over again every time. |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/16/14 at 12:52:24 hey Lancer,the muffler you sent me does not meet up with the mounting bracket it is about 3 inches forward, suggestions? I guess I expected plug and play... |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/17/14 at 03:47:50 3F3325333E3E2160606361520 wrote:
It is so common I didn't even think to mention it, but we rarely get a plug & play, instead needing a short piece of metal to use as a bracket to position it in our desired position. I usually grab a piece of scrap, cut and drill to what I want with a test fit & then paint black so it will disappear. Lock washers on everything. ;) |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/17/14 at 08:12:17 Thank you brother, I think I will take the bike to my guy because I don't have the needed tools, but I am going to wait until the jet's come. can you notify me when you send them please. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/17/14 at 09:05:16 3B3721373A3A2564646765560 wrote:
The JETSET was in a yellow folded bubble padded envelope in the box with the muffler. |
|
Title: Re: Lancer's Performance Parts Post by novicetinkerer on 03/17/14 at 11:51:30 It was hidden in the confetti. I am so glad that I didn't throw the box away yet. Thank you again. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/17/14 at 14:08:36 0F0315030E0E1150505351620 wrote:
Hahaha, glad you caught it before it went out in the trash ! |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 08/03/14 at 04:47:20 Some of asked: REX, a little while ago http://images1.snapfish.com/232323232%7Ffp9%3A%3B%3Enu%3D323%3A%3E639%3E697%3EWSNRCG%3D32%3B74%3A34%3B8339nu0mrj |
|
Title: Dyna muffler # 64941-01 is the direct bolt up Post by Knucklehead on 08/04/14 at 11:52:41 Dyna muffler #64941-01 is the direct bolt up Dyna muffler. You do need to make a gasket between the header pipe and the muffler but the mounting rail on the back of the muffler fits correctly to the 2 mount holes on the S40 frame. Use carriage bolts to not spin in the muffler rail; 8mm or 5/16th by 1". For the gasket I used aluminum sheet a bit thicker than a tin can. I cut a 1 1/2" strip and cut a 45 degree angle on each end that matched up after 2 circles of the header, 3 wraps wouldn't fit. I found 2 Dyna mufflers on ebay for $40 + $20 freight. They were like new perfect. Google "dyna muffler 64941-01". There are a number of them available on ebay today. |
|
Title: Re: Lancer's Performance Parts Post by swing69 on 02/02/15 at 16:34:38 Lancer. curious. what kind of performance numbers are you getting off the cams you sell?? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 02/03/15 at 04:03:00 292D33343D6C635A0 wrote:
It has been a while but the last time I had numbers they were: Setup: Stage 1 Cam; 36VM carb; cylinder had silicone carbide treatment but still running Suzuki piston with stock compression; outer ring on exhaust port of head opened to 1.6" to custom match header ID of 1.6"; good high flow muffler. (header/muffler shown in photo above) With that setup it was producing just over 40 hp at the rear wheel. 0-60 and 1/4 mile runs from a stop required hanging over the tank to keep the front end down and I was still not able to fully use everything it had until after rolling a bit. 0-60: 4.9 sec 1/4 mile: Trying to remember...but right around 12 sec, 11.9-12.1 area @ 90 mph. The bike at the time was a bit over 300 lbs & I was a bit over 200. Seems like the total wt. was like 525-530 lbs +/-. So I cannot really say what the Camshaft does all by itself, since I have not had JUST the Camshaft and no other modification in my engines. That said however, the Camshaft does determine the CHARACTER of the engine. The stock cam of the LS650 engine is "mild mannered" to say the least. A Performance Camshaft will give this engine some real ATTITUDE. These particular camshafts, the Stage 1,2 & 3, are not "Race" cams, but good efficient torque producing cams which is what this engine needs because that is what this engine is made to do, so you go with its strong points and enhance them. At this point I am only producing the Stage 3. I think it has the best qualities of the 3. |
|
Title: Re: Lancer's Performance Parts Post by foofopps on 03/20/15 at 18:52:58 big bore, performance cam, performance carb. Yeah I'll take one of each! |
|
Title: Re: Lancer's Performance Parts Post by j_osborne on 03/06/16 at 08:35:47 2007 S40 - stock Interested in most, if not all the Performance Package. Please send me PM with details. :) Thanks Lancer! |
|
Title: Re: Lancer's Performance Parts Post by Demin on 03/11/16 at 05:46:00 I sent you a couple PMs |
|
Title: Re: Lancer's Performance Parts Post by Anegative on 03/18/16 at 07:38:17 Ive never used paypal. once i send u the money on paypal. how will you know my address to send the part? does it ask in paypal? |
|
Title: Re: Lancer's Performance Parts Post by JustinB on 03/18/16 at 11:46:15 Hi lancer, I sent you an email yesterday. Interested in doing a bit bore build. Wish I could just pm you here but I need 10 posts to be able to do so. |
|
Title: Re: Lancer's Performance Parts Post by Anegative on 03/20/16 at 16:46:22 are you still around Lancer? I emailed ya about some jetsets.. |
|
Title: Re: Lancer's Performance Parts Post by vanna_brown on 03/22/16 at 06:34:35 I'm looking for lancer's email. can anyone help :o |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/22/16 at 07:12:28 4C63686A6C79647B680D0 wrote:
If you are in Columbia, MO. I got the Paypal |
|
Title: Re: Lancer's Performance Parts Post by striknein on 05/21/16 at 20:36:49 PM incoming. |
|
Title: Re: Lancer's Performance Parts Post by ero4444 on 06/13/16 at 09:51:13 LANCER can you confirm you got my payment for a jetset in Paypal - sent June10 - subject: JETSET for Suzuki Savage 2001 - putting on a Dyna muffer. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/14/16 at 04:16:03 6E79643F3F3F3F0B0 wrote:
If you are Eric, then yes, I got it. |
|
Title: Re: Lancer's Performance Parts Post by savageguy1 on 06/19/16 at 16:23:44 Where do you get the pistons ? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/19/16 at 18:45:19 362728222721342F3635460 wrote:
From Wiseco Piston Co. |
|
Title: Re: Lancer's Performance Parts Post by savageguy1 on 06/20/16 at 09:08:02 do have any cyclinder heads ? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/20/16 at 23:20:18 7F6E616B6E687D667F7C0F0 wrote:
I do. It is not perfect but usable. The rockers need to be replaced. One of the cam bearing surfaces is a little roughed up but can be smoothed out a bit and then be used. I can take care of the bearing surface and you do the rest. $150 for the head & head cover, I do the cam bearing, + shp in the US. |
|
Title: Re: Lancer's Performance Parts Post by webbrob on 07/03/16 at 20:27:55 PM sent about Performance Carburetor kit. |
|
Title: Re: Lancer's Performance Parts Post by webbrob on 07/19/16 at 11:14:44 Paypal payment sent as well. Just in case, Performance carb kit for a 2008 S40 with Dyna exhaust and K&N filter installed. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/19/16 at 13:19:05 7D6F68687865680A0 wrote:
Got ya covered dude ! |
|
Title: Re: Lancer's Performance Parts Post by cheapnewb24 on 07/19/16 at 20:00:20 When are you going to get your nitrided chains? I might be interested in one. Haven't decided for sure yet. |
|
Title: Re: Lancer's Performance Parts Post by robinsoncrusoe on 07/19/16 at 21:25:14 Do You have a Used and working Suzuki LS650 S40 Savage Boulevard complete Cylinder Head Assembly with Cam, also stock piston and rings?? Any deals with the hardened rocker pads as well. Core charge is understood. Cost of parts plus shipping to: Shipping to 33850. FL[font=Courier New][/font] |
|
Title: Re: Lancer's Performance Parts Post by webbrob on 07/20/16 at 12:46:22 58555A5751460603340 wrote:
Awesome! Thank you! Got ya covered dude ![/quote] |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/20/16 at 14:27:19 495459525548545558494E48545E3B0 wrote:
I do have a cylinder head, but it need some work. One of the cam bearing surfaces need a little attention; the rockers need to be replaced. There is no camshaft with it. I might have another stock cam available But know for sure yet. I have a good piston with its rings, but I have not checked to see if the rings are usable... They SEEM good. Michael |
|
Title: Re: Lancer's Performance Parts Post by Bobber on 08/27/16 at 20:06:39 Could you build a finished motor 50 hp? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 08/28/16 at 11:05:38 373A35383E29696C5B0 wrote:
************** I will not be home until late tomorrow; will check things then and get prices for you. **************+ I do have a cylinder head, but it need some work. One of the cam bearing surfaces need a little attention; the rockers need to be replaced. There is no camshaft with it. I might have another stock cam available But know for sure yet. I have a good piston with its rings, but I have not checked to see if the rings are usable... They SEEM good. Michael [/quote] |
|
Title: Re: Lancer's Performance Parts Post by Bobber on 08/28/16 at 18:23:12 I have a running 97 motor. |
|
Title: Re: Lancer's Performance Parts Post by Armen on 09/25/16 at 08:36:00 Hey Lance, What cam would you recommend for a stock motor with a 40mm Flatslide Mikuni (with K+N Pod), and a RYCA long muffler? Not touching the piston/cylinder for now, but I'll do a high compression 97mm eventually. My idea of a good time is a bike that pulls from 2K RPMs and has a wide power band. Don't love revving the nuts of the motor. thanks, -Armen |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/25/16 at 09:25:00 5F6C737B701E0 wrote:
I make just the Stage 3 Camshaft now, and as stated it is a middle of the road design that takes advantage of a large single cylinder engine, and the type of power it makes. The peak torque happens around 4500 rpm and the peak power at about 5500 rpm. Power and torque does not stop there but peaks out at those levels. You will feel the effects of this camshaft shortly after you come off idle, when compared to the stock camshaft. I think this is ideal for the LS650 engine. For a piston, I favor the 94mm High Compression piston we now have available. You get all of the benefits from the higher compression but do not need to bore your cylinder, and thus save a good bit of money. Keep in mind that with the 97mm piston, you gain 42cc in engine volume, which is a minor effect compared to the rise in compression ratio from 8.5:1 to 10.5:1. |
|
Title: Re: Lancer's Performance Parts Post by Armen on 09/25/16 at 09:38:17 Thanks Lance, I'm tracking down a core cam now. Have a complete 97mm top end with the cylinder all bored/honed/nitrided/fondled. I'll wait til I have the bike running a while til I do that. Ever play with the cam timing? Slot the holes in the cam sprocket and dial in the timing? thanks, -Armen |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/25/16 at 11:12:06 0D3E2129224C0 wrote:
Nope, never needed to mess with the cam timing, it works pretty good as is. If you wanna tweak the timing you could just play with the cam chain on the gear. |
|
Title: Re: Lancer's Performance Parts Post by Armen on 09/25/16 at 12:24:43 So, you have a Stage 3 in stock now? thanks -Armen |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/25/16 at 13:10:53 5F6C737B701E0 wrote:
Not in stock, your cam core is needed. I did have a few earlier this year but they are gone now. I am waiting on the return of cam cores. |
|
Title: Re: Lancer's Performance Parts Post by Armen on 09/27/16 at 13:10:47 Thanks Lancer. I'll scare up a core. Once you have the core, any idea how long til you have the tarted up ones? -Armen |
|
Title: Re: Lancer's Performance Parts Post by Armen on 09/27/16 at 13:30:30 Will a cam from a '96 DR650 work as a core? thanks |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/27/16 at 15:41:06 57647B7378160 wrote:
No, only model years 90-95 for the DR650 |
|
Title: Re: Lancer's Performance Parts Post by Simbaco on 11/28/16 at 23:16:05 I really need brake, throttle, and clutch lines... and possibly electrical? But I'm not able to PM yet? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 11/29/16 at 03:00:57 566C686764666A050 wrote:
I can help you with a brake line & clutch and throttle cables, but electrical lines will require you purchasing from other sources. I get stock items from Bikebandit.com, others use Ron Ayer, etc. |
|
Title: Re: Lancer's Performance Parts Post by Joer0952 on 12/24/16 at 11:47:38 Lancer I just wanted to let you know that I sent you a pm regarding the jetset and jetting my carb. Thanks, Joe |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 12/25/16 at 03:09:54 05202A3D7F767A7D4F0 wrote:
Sent Pm |
|
Title: Re: Lancer's Performance Parts Post by koehlerrk on 05/01/17 at 05:14:11 Thanks for the jetset, Lancer! Should have my wife's 03 running smooth in no time! |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 05/01/17 at 05:55:48 71757F72767F6868711A0 wrote:
;) 8-) |
|
Title: Re: Lancer's Performance Parts Post by Blueberet on 05/09/17 at 03:47:12 Hi LANCER! Trying to reach you from here as i cant send a PM and too shy to bump JETSET thread ;D I Sent you an iqnuiry about JETSETS earlier, do you have any left and will you post to Finland? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 05/09/17 at 06:58:06 5A746D7D7A7D6A7D6C180 wrote:
Yes, I can ship to Finland. The shipping cost is $32 for Priority (7-10 days) and $14 for First Class mail (10-14 days). I sent my last set out yesterday but have more on order and should have those by the end of the week. |
|
Title: Re: Lancer's Performance Parts Post by Blueberet on 05/09/17 at 07:56:51 Perfect, payment sent for first class mail -Joni |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 05/09/17 at 08:00:21 436D74646364736475010 wrote:
okie dokie |
|
Title: Re: Lancer's Performance Parts Post by SavageJack on 06/26/17 at 15:11:05 Once ordered, I had my Lancer Jet kit in hand within a week. Thanks Lancer for sourcing all this for us. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/26/17 at 16:15:27 0A382F383E3C13383A32590 wrote:
It is my pleasure. |
|
Title: Re: Lancer's Performance Parts Post by sgreiss on 09/01/17 at 08:17:08 This is great information! |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/01/17 at 08:23:07 53475245495353200 wrote:
Well thank you. I appreciate your comment and your enthusiasm ! |
|
Title: Re: Lancer's Performance Parts Post by mrpete on 11/02/17 at 14:00:09 Just wanted to say, "Thank You". Fast easy service! ...almost too easy. Now I'm eyeballing a few more items! Thanks again, -pete |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 11/02/17 at 14:25:24 0F1012071607620 wrote:
;) :D 8-) |
|
Title: Re: Lancer's Performance Parts Post by DragBikeMike on 03/25/18 at 01:39:01 I am interested in your 97mm piston kit and camshafts. Can you please give me the specifications for the Stage 2 & 3 cams (i.e. valve timing, total lift & TDC lift). Why do you recommend the spring kit for off-road only? How do I order and pay for these items? How do you ship? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/25/18 at 05:22:33 10161965676064540 wrote:
If you go back to page 1 of this thread you will see a list of Performance parts, select the one for Camshafts and that will take you to the spec's. The Spring kit is made for extremely high lift cam profiles, which mine are not. The springs in the kit will work in the LS650 but were made for the DR650 high lift cams for 1990-1995 model years. The cam core is the same as ours but the profile is quite different. I am making the Stage 3 cam only now. It works very well with the natural engine characteristics. The Stage 2 pushed the power too high in the rpm range to be useful for most of our riding, which is in the low and mid range. I have both the 97mm piston and 94mm pistons. 95% of the power gain is due to the increase in Compression from 8.5:1 to 10.5:1, with only a fraction from the increase in cylinder size from 650 to 695cc. Using the 94 also saves $$ by not having to bore the cylinder, just a good hone is needed. Payment is usually by PayPal, made to savage.s40@gmail.com. I can email you an invoice if you prefer using a credit or debit card. I also accept cash or checks as well. Cost of the Stage 3 cam is $299 with your cam core in exchange. If you need the Stage 3 cam before removing your old cam, in order to be able to ride while waiting for the new one, then a $100 refundable deposit is required, and will be refunded upon my receipt of your cam core. ** Current turn around time for a new cam to be manufactured is 5-6 weeks. At times I have a few in stock, but not always. I have 3 being made now and they should be ready in about 2 weeks. One of those is already paid for by another member, so 2 possible remaining. They do not last very long so if you want one then you need to process payment and you will be next on the list to receive one. I ship USPS Priority 2-3 day, fully insured, and shipping cost is included in the price. If I missed something or you have other questions just holler. Michael |
|
Title: Re: Lancer's Performance Parts Post by Pork chop on 03/25/18 at 14:12:15 looking to rebuild the top end of my 2002 savage , I looking for a big bore kit, reworked head and timing kit |
|
Title: Re: Lancer's Performance Parts Post by DragBikeMike on 03/26/18 at 15:10:02 I thinks I will start with the 97 mm oversize piston. I will eMail you at your gmail address and provide you with my shipping info. Send me a reply with the full cost including shipping and then I will do the PayPal thing. I have an account but I don't think I ever used it. If I get screwed up I will let you know. Thanks, Mike |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/28/18 at 03:42:24 Looks like I might not need to bore my cylinder , so I'm looking at a cam , carb, and piston, maybe the chain tensioner. ,if I need to decide between the carb and the cam what would be the best choice |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/28/18 at 03:48:54 I also wanted to ask if rockers need to be changed when you install a new cam , like the lifters on a car? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/28/18 at 05:02:39 0D353F382B6A6F590 wrote:
If you need to make that choice then go with the cam first. Your engine will already be disassembled so make the cam switch, you can always upgrade the carb later and not have to dig back into the engine. Just makes sense. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/28/18 at 05:04:38 :Dr 18202A2D3E7F7A4C0 wrote:
If your rockers show signs of wear then change them out. If not, then you are good. |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/28/18 at 08:48:40 Is the Verslave tensioner on eBay anywhere, or do you have any , I know you charge more on eBay , so how do I go about purchasing off of here , and what type of pay0ments are acceptable |
|
Title: Re: Lancer's Performance Parts Post by verslagen1 on 03/28/18 at 08:52:31 70484245561712240 wrote:
Check out the link below. |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/28/18 at 15:13:06 Looks like I'm going to have to bore the cylinder afterall |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/29/18 at 11:12:15 I am ready to order the piston , what sizes do you have available |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/29/18 at 11:13:34 also the machine shop said to be sure and ask if I needed a big bore head gasket |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/29/18 at 11:15:13 another question , I will need a rebuild kit is it better to buy suzukis full kit or is there a good one I can buy online for a better price |
|
Title: Re: Lancer's Performance Parts Post by Diamond T on 03/29/18 at 11:38:08 I should be able to order the cam this weekend , also wondering if the hard krome muffler would be a better choice than the gp shorty I have now |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 03/30/18 at 04:39:27 Pistons: 95, 96 & 97mm Stock head gasket is fine; there use to be someone on eBay that sold copper gaskets in assorted sizes but have not seen him for a while You can find gasket sets on eBay for decent prices The Hard Krome is quality built but even with the baffle it is a high flow muffler and is loud but is of a good size. Ideally, for good running, the inside volume of a muffler should be the same volume as the engine so try to avoid small mufflers and especially straight pipes. |
|
Title: Re: Lancer's Performance Parts Post by suzi-q on 09/16/18 at 17:42:12 hey lancer. is there any more of your cam chains? thanks |
|
Title: Re: Lancer's Performance Parts Post by Old Savage Eddie on 09/17/18 at 04:24:03 Hello Lancer, Would you happen to have a 94mm piston? I would also like to discuss with you how to proceed with an order for a stage 3 cam. Christmas is coming early this year ;D Eddie |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/17/18 at 06:06:29 4A4C43501448390 wrote:
Yes I do. $89 and includes shipping in the US. you can PayPal ... Savage.s40@gmail.com or I can send an invoice to your email address. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/17/18 at 06:14:36 5677777A765C130 wrote:
Yep, I’ve got some of the 94’s still. I have just one cam right now that is ready to go, and one I can send to Webcam to be made into a Stage 3, and that is taking 4-5 weeks before it comes back. First come first served. They don’t last long. Piston is $199 and the Stage 3 cam $299, ship. incl. As noted in the thread on the Camshaft your cam core is required in exchange for the Stage 3 upgrade, which can be sent now or after you pull your engine. If sent before I ship the Stage 3 to you then no extra charge, but if after then a $100 core deposit is required and that will be refunded upon my receipt of your core. Extra cores are hard to come by at a reasonable price. I have a couple that have been out for months, even with the core charge still outstanding on them. Yea, beats the heck out of me why they don’t send them. You can PayPal to Savage.s40@gmail.com or I can send an invoice to your email. |
|
Title: Re: Lancer's Performance Parts Post by madmikesmech on 09/03/19 at 09:33:34 Lancer, Top quality stuff you have my friend!!! Last year I purchased your JetSet, and the Allen head screw set for my stock carb. I'm sure you deal to to many other people to remember me, but, I have the free flowing Jardine turnout exhaust, raptor petcock, stock engine. Well you and I sent a few emails back and forth, and even a phone call or two! Well man, you know your stuff, you gave some helpful hints, and suggestions on jet sizes etc. Spot on!!!! 3800 miles this summer to date!!!! Problem NOW... due to the increase in power, and the age of probably the stock clutch components, I am experiancining a tad bit of clutch slippage!!!:( I feel it will make it thru this season, but EXPECT an order for clutch plates and spring this winter from me!!! Keep up the good work Sir, it is a pleasure to have you around !!![ch128077] |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 09/04/19 at 15:50:01 I remember you. My aging mind may have lost a few details along the way though. About your clutch, I assume you have adjusted it as far as possible already. Have you checked that little metal rod out on the end of the clutch Pak ? If that is no longer long enough another longer one should be available. It seems like there are 3 lengths, and if yours is one of the shorter ones then you can just swap it for a longer one. Also, it is possible that a set of stronger springs may solve your problems. The clutch plates used are pretty darn durable so unless they measure below specs don’t assume you need to order a set, a clutch Pak is $125. |
|
Title: Re: Lancer's Performance Parts Post by tophowe on 02/17/20 at 11:29:02 Lancer Do you have any big bore pistons, cams, and carbs left? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 02/17/20 at 12:11:58 213A253D3A2230550 wrote:
Yep, how many dozen do you need ? [ch128513] I have one each of the 95 & 96mm and several of the 94mm stock size Wiseco pistons. Camshafts and carbs are also available. Wiseco Pistons.............. $199 Carb kits...................... $399 for basic kit ** UFO, DAJ & QFTW extra if desired Stage 3 Cams............... $299 + $100 refundable deposit for usable core exchange I can send you an invoice to your email for use of your PayPal account, credit or debit account. You can process payment when you choose with it. Michael |
|
Title: Re: Lancer's Performance Parts Post by tophowe on 02/20/20 at 14:07:50 Could you please send me an email with the invoice for the 96 piston, stage 3 cam, performance carb and UFO |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 02/21/20 at 15:45:19 667D627A7D6577120 wrote:
I can do that; what email do you want to use ? Are you sure you want the 96mm instead of the 94mm Wiseco ? Same benefit of higher compression without having to bore unless your cylinder is gouged. |
|
Title: Re: Lancer's Performance Parts Post by Psydton3 on 05/27/20 at 01:20:20 Hi, Can you please send me an invoice for a throttle cable to suit a 2016 suzuki boulevard s40 for a mikuni vm36 carburetor? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 05/27/20 at 09:17:09 57747E6373686934070 wrote:
Yep. [ch128521] |
|
Title: Re: Lancer's Performance Parts Post by Jdvt600 on 06/11/20 at 21:36:22 PayPal payment sent! |
|
Title: Re: Lancer's Performance Parts Post by SandyRavage on 06/14/20 at 12:34:00 How do I order? I'm interested in the complete gasket kit. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/14/20 at 15:06:49 0D3F303A270C3F283F393B5E0 wrote:
You can just tell me here what you want to order. I accept direct PayPal payments or I can send an invoice to your email address with which you can use a card of your choice. My PayPal address is: Savage.s40@gmail.com A Complete Gasket Set is priced at $125 but I don’t have any in stock, that is an “occasional” item that is asked for. I can usually get one in a week. Michael |
|
Title: Re: Lancer's Performance Parts Post by Jdvt600 on 06/24/20 at 18:03:29 @Lancer, Got them installed and tuned with 55/152.5 and three washers. Thanks for everything! JD |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/26/20 at 05:56:44 You bet ! [ch128526][ch127949] |
|
Title: Re: Lancer's Performance Parts Post by flatout on 11/19/20 at 06:05:33 how do i getin touchwithyou? |
|
Title: Re: Lancer's Performance Parts Post by flatout on 11/19/20 at 06:06:46 i am new to forum and need parts for engine build |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 11/19/20 at 08:38:47 101814121414210 wrote:
I just sent you a PM which I think you can answer. If not my email is savage.s40@gmail.com. If you email let me know your ID used here so I can connect the two. |
|
Title: Re: Lancer's Performance Parts Post by JoshuaxxLewis on 12/07/20 at 10:28:57 Good afternoon, My name is Joshua Lewis and i'm new to this forum, or any forum for that matter. One of my many projects is an 08' Suzuki s40. I need to buy on of your Stage 1 or 2 carb re-jet kit. I was recommended to you by a guy on Instagram that said you had what i need for around 1/3 the cost of the Dynojet kit. Please let me know on here or email me at joshuaxxlewis@gmail.com for ordering information. Thank you in advance for any help with this!! sincerely |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 01/10/21 at 10:30:15 15302C372A3E2727133A28362C5F0 wrote:
Sent you an email |
|
Title: Re: Lancer's Performance Parts Post by Jdvt600 on 05/28/21 at 11:14:28 PM sent. vm36 kit w/UFO |
|
Title: Re: Lancer's Performance Parts Post by ErikDrum4Savage on 05/28/21 at 14:34:52 Lancer, I bought an awesome 2009 S40 but wanted to switch out the carb as the bike sat for a long time and based on all advice I have gotten and reading done on this site, this is where my issues are sitting. I feel more comfortable swapping out instead of trying to tear apart and rebuild, and I see you have offered complete kits in the past for a VM36 but not seeing a recent post for what 'I think' I need. If you can give me the whole shebang with throttle cable and flange, I am very interested, or help with how to go about it is appreciated too as I found the VM36-4 online but may need accessories from you to make it all work. I am a nube to the site and don't have PMs unless I can respond to something you send me, or I can email you at the address you posted above if easier, just let me know and thank you for the help! Erik |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 05/29/21 at 04:05:47 26110A082711160E57300215020406630 wrote:
Howdy The Carburetor kit contains: 36mm VM carb New rubber flange Throttle cable Jet Pak with extra jets Carb manual printout Carb tool Uni air filter Spark plug $399 including shipping in US PAYPAL to Savage.s40@gmail.com Or Send check cash or money order to: Michael Eslick 32810 S 265 Rd Henryetta, OK 74437 |
|
Title: Re: Lancer's Performance Parts Post by ErikDrum4Savage on 06/29/21 at 20:01:59 Awesome, thank you Lancer! I sent the PayPal to you and I can’t wait to get this thing swapped out and ready for some good days this summer. If you have the parts on hand and I can kick you a few extra for rush shipping, let me know, with a long weekend I can do some damage! Cheers. Erik |
|
Title: Re: Lancer's Performance Parts Post by 1stepcloser on 07/19/21 at 15:19:31 Howdy, do you have a carb kit for an '87? And, can the stock airbox still be used? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/20/21 at 05:04:32 0745425346555A59455344360 wrote:
Yes, the carb kit will work on an ‘87, and it is possible to use the air box. $399 incl. shp. Cash, check, MO, credit, debit, PayPal. |
|
Title: Re: Lancer's Performance Parts Post by 1stepcloser on 07/20/21 at 11:20:57 Excellent! So, how do I pay through PayPal? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/20/21 at 11:28:54 7B393E2F3A292625392F384A0 wrote:
I can send you an invoice through PayPal to your email that makes it easy for you to process. Send me an email and I will send you the invoice payment request. |
|
Title: Re: Lancer's Performance Parts Post by 1stepcloser on 07/20/21 at 13:02:05 Email sent. Thank you. |
|
Title: Re: Lancer's Performance Parts Post by Dreanimal on 08/27/21 at 03:54:37 PM sent |
|
Title: Re: Lancer's Performance Parts Post by Adellemoto on 12/04/21 at 20:00:13 Hey Lancer, Any chance you have any of those 94mm (just to replace the stock) pistons in stock? Also, do you still get the good gasket sets? If so I'd like to get a piston and a gasket set off ya. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 12/05/21 at 04:22:39 4A617B607A686D6C65656C090 wrote:
None of the newest version in stock but they are on order with Wiseco. I do have 2 of the older version, 9.5:1 CR in stock. The 97’s are also being manufactured and they are due in a couple of weeks. |
|
Title: Re: Lancer's Performance Parts Post by Adellemoto on 12/05/21 at 16:51:01 you have a lead time for the 10.5:1 94mm will be in? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 12/06/21 at 03:58:23 775C465D47555051585851340 wrote:
Expecting in early Jan. ‘22 |
|
Title: Re: Lancer's Performance Parts Post by Rivenin on 12/06/21 at 07:29:23 payment sent for the uni filter and jetset. (mostly using this to get my post count past 10 ) 8-) |
|
Title: Re: Lancer's Performance Parts Post by QNero on 12/09/21 at 12:10:53 Hey Lancer, I think I need new Valve springs? I have a link on Rubber side down. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 12/10/21 at 11:47:00 120D26312C430 wrote:
I don’t stock that item, check bikebandit.com |
|
Title: Re: Lancer's Performance Parts Post by sparktfxr on 02/20/22 at 16:28:15 Thanks Lancer..got the piston & thanks to everybody involved in its development & for making it available...awesome..Cheers |
|
Title: Re: Lancer's Performance Parts Post by Jdvt600 on 05/28/22 at 08:04:17 Emailed you |
|
Title: Re: Lancer's Performance Parts Post by Theduderino on 06/23/22 at 13:46:08 Oh Henrietta, That reminds me of long trips in the backseat of an Eldorado Cadillac. Going to visit my great grandmother! Not a whole lot in Henrietta |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/23/22 at 13:59:57 But wait, there’s more ... we just got a Quick Trip truck stop/auto gas station in Henryetta ! Yep. |
|
Title: Re: Lancer's Performance Parts Post by och on 07/20/22 at 15:40:22 This is a pretty long threads, trying to make a comprehension of it for the upcoming winter project. I understand that with the performance carburetor there is no need for jetset, is that correct? I terms of sequence, I imagine its best to do both the piston and the cam together, once the engine is being take apart. But also, in terms of sequence, if I only have the cash for either the car or the piston + cam, is it better to do the carb first or the piston + cam? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/21/22 at 06:42:24 777B70180 wrote:
************** The stock CV carb and the VM carb use a totally different set of jets. Which is better, to swap the carb first or the piston & cam first ? Well, that depends ... on whether the budget and/or working time is most important. Cost and time for a carb swap is less, cost & time for a cam/piston swap is a bit more. The cam and piston will yield more hp & torque than the carb, but the carb is easier to do. What is your preference ? |
|
Title: Re: Lancer's Performance Parts Post by och on 07/21/22 at 08:10:15 I think I'll just do the carb, at least this winter. I'll be ordering it from you sometime this fall, unless I can convince the wife that I absolutely need to spend the $ on it right now, lol. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 07/21/22 at 13:04:28 5B575C340 wrote:
Wife needs convincing ? ? Hmmm. Just TELL her “I NEED these things woman”. Nuff said. [ch128526] |
|
Title: Re: Lancer's Performance Parts Post by Steddy58 on 08/13/22 at 18:29:31 Hi Lancer I bought the stage 3 cam and a wiseco piston, put it together and it was excellent. I have a mikuni vm36 carb and until a month or so ago it was running like a swiss watch as my oppo said ( who knows more about bikes than he does swiss watches ). Anyways there appeared a nasty rattly noise so after a bit i realised it wasn't going to cure itself so I took the head cover off and the rocker pads and the lobes of the cam look like had been having serious problems the cam lobes looked like they had been worn down to the original profile. Any ideas of what I did wrong or failed to do right? many thanks in advance Steddy I've tried to enclose pics but it will only let me put one up |
|
Title: Re: Lancer's Performance Parts Post by och on 08/28/22 at 20:06:04 Hi Lancer, I sent you a PM and an email. |
|
Title: Re: Lancer's Performance Parts Post by Leon on 04/20/23 at 15:34:59 Lancer saw your post for the Right side control assembly "Starter Button for $15 I want it as long as it will work on a 2000 Savage. I have a number of other parts I need also .I have no air cleaner, air box ,Tool Box or side covers I could use a new exhaust as well and Possibly a jet kit my bike pops whn turned off so i think it runs lean as well as the header pipe is turning blue. I am new to the Savage/ Boulevard Cruisers . Migh want one of your forward control sets also. Email me at Hammerman Thirty Five at juno.com for some reason I am not getting notified of post on here. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 04/21/23 at 03:38:16 59707A7B150 wrote:
I may have some of the parts you need but will need to check. I don’t have or sell forward control sets, those are from a different forum member. Sending you a PM |
|
Title: Re: Lancer's Performance Parts Post by LilChop on 06/12/23 at 22:21:09 Are these performance packages still available? I am interested in the carb upgrade kit. Please get back Lancer. |
|
Title: Re: Lancer's Performance Parts Post by LilChop on 06/12/23 at 22:28:09 Will carb kit work on the 2018 s40? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/13/23 at 18:21:27 755055147A515649390 wrote:
The carb kit will work on all model years of LS650 Savage or S40. Carb kits are in stock. $429 with shipping included for US addresses. PayPal payment to “savage.s40@gmail.com” |
|
Title: Re: Lancer's Performance Parts Post by LilChop on 06/15/23 at 16:57:57 How much is shipping to Toronto Canada ? |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 06/17/23 at 17:23:40 163336771932352A5A0 wrote:
Shipping is $61 toToronto (USPS Priority), which would be added to Kit price. |
|
Title: Re: Lancer's Performance Parts Post by LilChop on 06/26/23 at 18:30:21 Ok great, thanx Lancer. Interested in the piston and camshaft stage 3 as well. Would pm you but it’s not functioning yet. |
|
Title: Re: Lancer's Performance Parts Post by Chromehead on 11/09/23 at 04:50:59 Would like a stage 3 cam, and a jetkit for stock carb. Let me know what bolt /hardware kit would upgrade assembly. Thanks. |
|
Title: Re: Lancer's Performance Parts Post by LANCER on 11/09/23 at 13:58:50 557E64797B737E737772160 wrote:
Hardware assembly for what ? There is no hardware upgrade required for installing a Stage 3 cam or a Jetset. |
|
Title: Re: Lancer's Performance Parts Post by ThumperPaul on 09/22/24 at 05:57:24 Lancer, see your messages please. |
|
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |