|
SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> The Marketplace >> RYCA take off's /cgi-bin/YaBB.pl?num=1541018498 Message started by verslagen1 on 10/31/18 at 13:41:38 |
|
Title: RYCA take off's Post by verslagen1 on 10/31/18 at 13:41:38 A lot of parts, take offs from RYCA builds. Let me know what you need and I'll see if I have any. Make offer. http://suzukisavage.com/yabb2.2/Attachments/s-l1600_006.jpg http://www.savageriders.com/verslagen/ForSale/seats.jpg http://www.savageriders.com/verslagen/ForSale/fenders.jpg Tank emblems qty about 100-200 pairs Get one for your hat! Fuel Tanks qty 3 dents on all of them Front and rear rims Air boxes and charcoal canisters Cylinder head qty 1 prob good for parts only Engine parts and hardware Clutch parts and springs Rear sprockets / pulleys Front sprockets / pulleys Turn Signals Front brake rotors Rear drums / hubs Factory speedometers with various mileage Decompression solenoids Engine side covers and clutch cover case sides. Reflectors Axles front and rear Horns Factory tool kits Factory fork springs Front seats Rear seat pillions torn Solo seat torn Engine case trim and top covers Rear oem fenders various colors and condition Front fenders dented repairable Shocks Side covers Mirrors Engine bolts Starter solenoid Fuel valves / petcocks Front brake lines Chrome belt guard upper and lower Triple tree tops Triple tree bottoms Buckhorn handlebars Drag bar Risers Foot controls and parts Chrome battery boxes Factory muffler mount / bracket Tank mount rubber bushings front and rear |
|
Title: Re: RYCA take off's Post by UglyBrute on 06/14/19 at 06:40:42 Would these parts be compatible with a 2009 S40? I need a front right foot-peg and a rear right turn-signal if they are available. Email: grungemonkey.bw@gmail.com |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/14/19 at 08:39:45 I'll have to see what I got, most likely not prime condition. |
|
Title: Re: RYCA take off's Post by SavageMan99 on 06/15/19 at 06:19:53 How much for the tall risers? |
|
Title: Re: RYCA take off's Post by Violent_Rage on 06/15/19 at 09:56:19 Hi, how much for: - two complete (left, right, front and rear) foot controls - two complete (left and right) hand controls - two complete rear turn signals - one speedometer with cable - two left and two right mirrors Do you also have a dyna silencer? I had an accident two weeks ago... :'( |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/15/19 at 17:24:02 5466716660624A66693E3E070 wrote:
$20 + shipping let me find them 1st |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/15/19 at 17:29:17 66595F5C555E446F62515755300 wrote:
Shipping to italy is $100, are you sure you want me to pull this together? |
|
Title: Re: RYCA take off's Post by SavageMan99 on 06/15/19 at 19:29:40 Sounds good. |
|
Title: Re: RYCA take off's Post by Violent_Rage on 06/16/19 at 01:10:36 7C6F7879666B6D6F643B0A0 wrote:
Shipping to italy is $100, are you sure you want me to pull this together? I searched for spare parts in Europe but it seems we're running out of Savage here, so, yes. :) To make shipping more convenient, add also front and rear pulley, a chrome battery box and shocks [/quote] |
|
Title: Re: RYCA take off's Post by SoC on 06/16/19 at 11:31:29 Looking for left and right side covers. |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/16/19 at 11:56:30 39383D2F2C2F203D25274E0 wrote:
Color? |
|
Title: Re: RYCA take off's Post by SoC on 06/16/19 at 12:56:44 Painting so color doesn't matter. |
|
Title: Re: RYCA take off's Post by Zonablazer on 06/18/19 at 01:41:14 Versy do you still have any header pipes? Mines badly rusted after previous owner left it in the rain for years. |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/19/19 at 20:37:45 695C5D52515F52495641330 wrote:
No headers. |
|
Title: Re: RYCA take off's Post by stewmills on 06/25/19 at 13:19:27 How about a clean left front foot peg for a 2008? Mine is slightly bent and I may beat it back in shape, but if the price is right I'd rather just slap a good 'un on there. Ship to 36879. |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/25/19 at 13:25:01 484F5E4C56525757483B0 wrote:
I have some that bent a little and the bottom ground off... is that good for you? |
|
Title: Re: RYCA take off's Post by stewmills on 06/26/19 at 07:06:05 Ha...that is pretty much where I am at now, but just bent a tad and no grinding. I'll just hammer mine out and should be good. I was just trying to avoid any real work ::) |
|
Title: Re: RYCA take off's Post by Fabricio Bino on 06/28/19 at 04:35:04 I am looking for a front right foot peg, is there any available? |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/28/19 at 08:04:09 313635253E343E387931323B3E24353E3938570 wrote:
I'm sure there is, but are you going to pay $35 or $60 for a beat up $5 part? |
|
Title: Re: RYCA take off's Post by SoC on 07/01/19 at 21:00:14 Just to let you know box arrived today, parts look great. Thanks so much. Now have a full set of tins to paint in one shot with out taking my daily ride apart. |
|
Title: Re: RYCA take off's Post by philthymike on 07/04/19 at 20:35:19 Would you accept $10 for a battery box? |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/04/19 at 21:56:31 697170756D71607470727C190 wrote:
Yes for just the box, maybe a top, no holder, no chrome tool box. Plus shipping of course. |
|
Title: Re: RYCA take off's Post by philthymike on 07/05/19 at 04:35:11 Just need the box by itself. Mines rusted up badly. |
|
Title: Re: RYCA take off's Post by UglyBrute on 07/21/19 at 17:23:11 How much for a set of rear turn signals? Preferably 2009, but if anythings fits... |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/21/19 at 20:02:32 5C6E65704B7B7C7D6C090 wrote:
I only have pieces and parts left. The plastic shell comes off the rubber mount. The wiring and socket can be separated. and the lens is removalable. What do you need? and what do you have that's usable? |
|
Title: Re: RYCA take off's Post by UglyBrute on 07/22/19 at 06:36:57 7F6C7B7A65686E6C6738090 wrote:
I only have pieces and parts left. The plastic shell comes off the rubber mount. The wiring and socket can be separated. and the lens is removalable. What do you need? and what do you have that's usable?[/quote] I need the entire rear right signal, the only part I have left is the metal stem from the rubber mount. :-/ |
|
Title: Re: RYCA take off's Post by dcaplinger2 on 07/26/19 at 05:20:11 Anymore chrome battery covers left? Also need an exhaust mount. |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/26/19 at 07:23:20 474042534F4A4D44465111230 wrote:
Do you mean the top or the tool box cover? Do you mean the muffler bracket? |
|
Title: Re: RYCA take off's Post by CharlieB on 08/11/19 at 22:34:50 Hello, Do you have a L frame cover (ECU cover) in black? I have a 2009. Also, thanks for replying to my post about my L turn signal/electrical short. - Carlos cmaduena@gmail.com |
|
Title: Re: RYCA take off's Post by uigiroux on 08/21/19 at 12:58:06 Interested in the front, left and right turn signals. Please reply asap! Thank you for your help! Also, as a secondary item, Id be interested in the foot pegs. Only if I can get the turn signals first though. |
|
Title: Re: RYCA take off's Post by verslagen1 on 08/21/19 at 13:38:27 2A3638362D302A275F0 wrote:
I have a lot of the old 'lollypop' style signals, but only a few pieces of the new style 'bullets'. Please note that both old and new styles can be taken apart and put back together to replace a broken piece. As far as footpegs go, I have a lot of passenger pegs. and a few bent fronts. |
|
Title: Re: RYCA take off's Post by verslagen1 on 08/21/19 at 20:53:09 Did I mention I got seats? 312F2D292B2C1D202E3727420 wrote:
http://www.savageriders.com/verslagen/ForSale/seats.jpg |
|
Title: Re: RYCA take off's Post by JohnsonLager on 10/12/19 at 12:39:50 How much you looking to get for a gas tank? |
|
Title: Re: RYCA take off's Post by mjg1088 on 03/12/20 at 07:39:15 I am looking for a master cylinder side mirror mounting bracket, any chance you have one available? Bike fell over in a windstorm and broke mine. |
|
Title: Re: RYCA take off's Post by verslagen1 on 03/12/20 at 08:28:57 6D6A6731303838000 wrote:
No, just bought one on ebay.~$20 |
|
Title: Re: RYCA take off's Post by srinath on 03/12/20 at 12:31:46 Vers - You have a seat still ? How much is the single rider/passenger one that may be a mustang or other. And also a smooth one without the ribs of the stock one. Also you still have that 6" riser ? Lemme know how much ?? And shipping. Shipping to 29063. Cool. Srinath. |
|
Title: Re: RYCA take off's Post by verslagen1 on 03/12/20 at 14:06:03 2A2B3037382D31590 wrote:
Can you indicate which one in the pic? Top is a corbin or which row, left or right. |
|
Title: Re: RYCA take off's Post by srinath on 03/12/20 at 14:47:16 7D6E7978676A6C6E653A0B0 wrote:
Can you indicate which one in the pic? Top is a corbin or which row, left or right.[/quote] Corbin may be an over kill for what I want, cos I've likely got some mods to seat in mind - but how much for that corbin ? Then the left row right below that corbin - is that on the stock pan ? Bottom most right row - again on the stock pan ? And those risers from S40 - how much for those. Either of those - who much. Thanks. Srinath. |
|
Title: Re: RYCA take off's Post by verslagen1 on 03/12/20 at 15:11:12 4D4C57505F4A563E0 wrote:
I'll get back to you. |
|
Title: Re: RYCA take off's Post by srinath on 03/12/20 at 15:16:03 23302726393432303B64550 wrote:
I'll get back to you.[/quote] Corbin isn't needed for my use. I'll pass. I need stock pan seat on anything. Basically check on the risers. That's all I'd want at this point. Cool. Srinath. |
|
Title: Re: RYCA take off's Post by Cbiscut05 on 03/29/20 at 12:07:35 How much for both parts of the 2 piece seat??? |
|
Title: Re: RYCA take off's Post by verslagen1 on 03/29/20 at 15:57:13 4C6D667C6C7A7B3F3A0F0 wrote:
which one in particular? |
|
Title: Re: RYCA take off's Post by Cbiscut05 on 03/29/20 at 18:19:25 5F4C5B5A45484E4C4718290 wrote:
which one in particular?[/quote] A front and back for a 88 savage |
|
Title: Re: RYCA take off's Post by verslagen1 on 03/29/20 at 21:49:55 05242F352533327673460 wrote:
which one in particular?[/quote] A front and back for a 88 savage [/quote] In the pic... which one? |
|
Title: Re: RYCA take off's Post by Cbiscut05 on 03/29/20 at 22:01:23 677463627D7076747F20110 wrote:
which one in particular?[/quote] A front and back for a 88 savage [/quote] In the pic... which one?[/quote] Bottom left for the front and middle on for the back |
|
Title: Re: RYCA take off's Post by Eggnog0890 on 05/01/20 at 09:51:40 Do you happen to have the chrome locking cover that goes on the battery box? If so,how much? I have a 2006 s40 |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/01/20 at 10:41:04 for a $1000 I'll give you the 1 off my bike. ;D |
|
Title: Re: RYCA take off's Post by Eggnog0890 on 05/01/20 at 12:01:30 Oof,well I'll let you know when I win the lottery lol. thanks for the quick reply |
|
Title: Re: RYCA take off's Post by srinath on 05/01/20 at 15:54:39 6B6A7176796C70180 wrote:
Vers - risers price please. Cool. Srinath. |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/01/20 at 20:23:18 5E5F44434C59452D0 wrote:
Vers - risers price please. Cool. Srinath.[/quote] I have 3 pairs, 2 are from the newer style, but I don't have the clamps with the bridge - $15 1 is from the early style with clamps - $20 |
|
Title: Re: RYCA take off's Post by srinath on 05/04/20 at 10:54:13 342730312E2325272C73420 wrote:
New is the one I want, but That bridge is needed right, its got the bottom 1/2 of the handlebar carrier. Cool. Srinath. |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/04/20 at 11:46:14 The newer risers engage with the clamps to keep them from turning. Also, just using regular clamps with them won't look right. |
|
Title: Re: RYCA take off's Post by MaxFubar on 05/07/20 at 09:06:27 How much for a set of the side covers? |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/07/20 at 10:24:15 6D41586655424152200 wrote:
I only have right sides. |
|
Title: Re: RYCA take off's Post by Mechaniac on 05/18/20 at 15:44:51 The Buckhorn handlebars, were those stock equipment in the past? Wife's 2014 has a flat style and she's short so I'm looking for some Buckhorns. What are the dimensions, overall width, rise, and center width. I'm also trying to figure out if I moved the controls back will I need longer cables and hoses etc. Thanks for any help Vernon |
|
Title: Re: RYCA take off's Post by Mechaniac on 05/20/20 at 18:29:19 Any comments Verslagen? |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/20/20 at 21:51:53 7A52545F56595E5654370 wrote:
they're 28" wide and 7" tall when the grips are laying on the ground. And they pull back about 9". |
|
Title: Re: RYCA take off's Post by verslagen1 on 12/03/20 at 13:34:26 2426747F7D732620160 wrote:
various lens covers available. |
|
Title: Re: RYCA take off's Post by LS650THUMPER on 03/24/21 at 15:45:29 what parts do you have left, been awhile since anyone posted , ty |
|
Title: Re: RYCA take off's Post by verslagen1 on 03/24/21 at 17:23:56 I have a lot of various stuff. let me know what you want and I'll look for it. |
|
Title: Re: RYCA take off's Post by 2Concours on 04/19/21 at 15:45:47 Hello Do you have the Right Side Cover that goes on behind the battery that will fit a 2011 Orange if you have one!!!!! |
|
Title: Re: RYCA take off's Post by verslagen1 on 04/19/21 at 16:37:53 78455E4455420001300 wrote:
I have red, black or silver. |
|
Title: Re: RYCA take off's Post by Murphdawg on 05/25/21 at 17:42:56 Hi I’d like to purchase a left side cover, a right foot peg (or both of need be but really only need the right) with rear break pedal (break line as well if you have it). Please let me know the total and I will send payment however you like. Much appreciated |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/25/21 at 19:11:32 0B3334362E22273121460 wrote:
What year do you need? I'm sure I have an '88 stator cover definitely not 100% shiny. I have several right brake assy's including the cable. Not sure if they have the brake switch cable. Might be able to find a peg, but I'm sure the end will be ground up. |
|
Title: Re: RYCA take off's Post by Graven754 on 05/25/21 at 19:12:53 Hey! How much for one of those stock tool kits? |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/25/21 at 19:32:22 516477607378212322160 wrote:
$20 not including shipping. |
|
Title: Re: RYCA take off's Post by Fabricio Bino on 05/27/21 at 06:56:04 are there any speedometer and rear brake cables left? |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/27/21 at 07:45:25 4C4B485843494345044C4F464359484344452A0 wrote:
Yes $5 each plus $40 shipping |
|
Title: Re: RYCA take off's Post by Fabricio Bino on 05/27/21 at 09:00:53 PM sent |
|
Title: Re: RYCA take off's Post by Louel on 07/07/21 at 10:03:31 Hi Are there any left front pegs left? Will it fit an '03 savage? Thanks |
|
Title: Re: RYCA take off's Post by SoC on 07/07/21 at 21:19:11 Versy, If you have another tool kit I will take one. Let me know and I will get payment out to you and PM address. |
|
Title: Re: RYCA take off's Post by Crowman on 07/12/21 at 17:42:11 Do you have a wiring harness and rear break light switch for 1986 suzuki ls 650 savage ? Thanks |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/12/21 at 20:26:52 6B7A677F656966080 wrote:
I know I have one off an 88, off of one of my bikes, known working with no 'fixes'. and I have another unknown condition/year. I think there are bullet connectors in various locations instead of the more 'modern' connectors they have in later years. |
|
Title: Re: RYCA take off's Post by Crowman on 07/13/21 at 18:00:49 Hello, what is the price of the wiring harness both the one from the 88 and the unknown one ? ? do you have a rear brake light switch if so what is the price ? Thanks so much. |
|
Title: Re: RYCA take off's Post by Crowman on 07/15/21 at 20:26:51 Can you please give me a price on both wiring harnesses. And do you have a rear brake light switch? Thankyou |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/16/21 at 07:02:48 I'm checking compatibility with the different year wiring harness to controls. Can you send pics of the connectors for the controls? |
|
Title: Re: RYCA take off's Post by Louel on 07/20/21 at 09:23:17 Hello Do you have a battery/tool box cover that will fit an '03 Savage? Thanks |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/20/21 at 09:29:51 032D2E3C26232620767B4F0 wrote:
sorry, no. |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/20/21 at 09:33:00 01100D150F030C620 wrote:
It appears that I've sold the '88 and the ? is for another bike I have. |
|
Title: Re: RYCA take off's Post by Crowman on 07/20/21 at 09:35:31 So you have nothing ? |
|
Title: Re: RYCA take off's Post by verslagen1 on 07/20/21 at 10:24:54 23322F372D212E400 wrote:
No spares harnesses available. |
|
Title: Re: RYCA take off's Post by verslagen1 on 11/15/21 at 14:54:23 check out the passenger foot pegs... http://suzukisavage.com/yabb2.2/Attachments/s-l1600_006.jpg |
|
Title: Re: RYCA take off's Post by MaconMan77 on 11/29/21 at 17:20:28 Still have handlebars? |
|
Title: Re: RYCA take off's Post by verslagen1 on 11/29/21 at 17:44:47 507C7E7273507C732A2A1D0 wrote:
I have many buckhorns. you pay shipping and they're yours. |
|
Title: Re: RYCA take off's Post by MaconMan77 on 12/01/21 at 08:25:20 I sent a message |
|
Title: Re: RYCA take off's Post by Rivenin on 12/02/21 at 19:15:47 it'll probably be expensive, but just checking - how much would a gas tank be shipped to 97128? i need a base for painting |
|
Title: Re: RYCA take off's Post by TBR125 on 12/24/21 at 19:56:01 If you still have one how much would a header cost? Also, do you have a left driver foot peg? |
|
Title: Re: RYCA take off's Post by verslagen1 on 12/24/21 at 21:20:57 4B706F7C777077190 wrote:
$60 and that doesn't include packaging. |
|
Title: Re: RYCA take off's Post by verslagen1 on 12/24/21 at 21:23:12 6A7C6C0F0C0B13080B0E3E0 wrote:
No headers. I have a peg, but it was straightened so it's not looking pretty. |
|
Title: Re: RYCA take off's Post by TBR125 on 12/24/21 at 21:47:03 Ok, Thanks for checking. My peg has been straightened twice so time to fab a pair. I do need a cam tensioner. How much is one If I send mine in? I've got 5,600 miles on it and want to replace it while I'm doing other engine work. |
|
Title: Re: RYCA take off's Post by verslagen1 on 12/25/21 at 05:25:57 6A7C6C0F0C0B13080B0E3E0 wrote:
594A5D5C434E484A411E2F0 wrote:
|
|
Title: Re: RYCA take off's Post by daphil on 03/31/22 at 05:52:22 Hey Verslagen, I am looking for any and all of the following parts. I listed an offer but I am open to negotiation: Horn - $55 Front left foot peg bar, rubber, and cushion - $45 Left passenger foot peg - $50 Left mirror - $50 Right mirror - $50 Header pipe - $150 Rear left turn signal - $35 Left shock - $150 Left shock top nut - $5 In addition, I had a question about the solo seat: does it bolt on directly to the stock frame or does it need some brackets/welding? If it’s not too much trouble to mount it, I’d like that too. Im in New York City, so you can give me a quote for the shipping cost. Thanks! |
|
Title: Re: RYCA take off's Post by verslagen1 on 03/31/22 at 07:17:29 OOPS! I got your email, but was in the middle of something and forgot. Most the parts I have are not in pristine condition, so I wouldn't expect those prices. Horns, got 'em. Front pegs, I got a couple left that I straightened from looking like horse shoes and I don't trust them. Passenger pegs, got 'em. Mirrors, I got a couple. Header pipe, nope. Turn signals, I got bits and pieces, nothing whole of the bullet style, but lots of the lollypop style. Shocks, I got several, all a bit rusty, might clean up. Shock nuts, don't think so. I pull the parts together and let you know. |
|
Title: Re: RYCA take off's Post by MirageJack on 04/26/22 at 16:53:40 I'd like to order! Turn Signals: May I please order a set of rear turn signals, and a front left? Are they interchangeable? I might just take 4, if so. Lamp cowl: The outer rim bit of the headlamp. Doesn't specifically say you have these, but I figured I try! Grip end-caps (2): Same as above. Ready to pay! |
|
Title: Re: RYCA take off's Post by verslagen1 on 04/26/22 at 20:42:23 14302B383E3C13383A32590 wrote:
I don't have any shells undamaged left Quote:
I don't have any of these Quote:
I have plenty of these you have mail |
|
Title: Re: RYCA take off's Post by Thumperman on 05/15/22 at 11:43:41 Do you have a front fender? |
|
Title: Re: RYCA take off's Post by TheSneeze on 05/16/22 at 07:05:09 I have two. |
|
Title: Re: RYCA take off's Post by TheSneeze on 05/16/22 at 07:06:47 55716A797F7D52797B73180 wrote:
I have a few turn signals, and a couple of headlights. |
|
Title: Re: RYCA take off's Post by SynthGeek on 05/26/22 at 20:00:12 LOOKING FOR A LEFT FRAME COVER Saw you had some of the right frame covers at one point, do you have any for the left side (the one that covers the ignition module)? And if so what price? |
|
Title: Re: RYCA take off's Post by verslagen1 on 05/26/22 at 20:53:38 2D3B3E272A7F29364E0 wrote:
I don't have any of the lefts, but several rights. |
|
Title: Re: RYCA take off's Post by SynthGeek on 05/26/22 at 21:09:48 That's too bad - thanks for the reply, Lefts seem hard to come by right now... |
|
Title: Re: RYCA take off's Post by Needles on 06/23/22 at 09:17:26 Battery box cover, side cover and tool kit cover? I have a 2002. |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/23/22 at 12:55:47 143F3F3E363F295A0 wrote:
Top? I have a couple I don't have any of the lefts, but several rights. None |
|
Title: Re: RYCA take off's Post by Needles on 06/23/22 at 14:10:58 How much for the top battery box cover? Oh, yeah, I meant the side cover for the battery box (right side); it might BE the toolkit; the base of the tool kit that goes to the right side of the battery box. I may have to fabricate one... |
|
Title: Re: RYCA take off's Post by verslagen1 on 06/23/22 at 17:56:29 614A4A4B434A5C2F0 wrote:
For the battery top cover, $15 inc shipping providing it's domestic. No chrome tool kit cover I might have the black battery retainer, add $5 if it will fit in the small box with the cover. |
|
Title: Re: RYCA take off's Post by Fabricio Bino on 07/27/22 at 11:41:11 Do you have the left and right top of engine covers? How much would be for them both? |
|
Title: Re: RYCA take off's Post by verslagen1 on 09/24/23 at 12:15:02 I have 3 ignition switches, 2 stock 1 with extended cable. They have the tape with the key code although barely readable. No keys. Also have 7 helmet locks, sorry no keys. Can be unlocked so they can be rekeyed. If you send a key, I can try rekeying, but not guaranteed. I have limited wafers. |
|
Title: Re: RYCA take off's Post by Fabricio Bino on 11/18/23 at 03:04:02 are any of those ignition switches actually readable? i might buy one and make a thousand keys for it, as i am a professional in loosing them |
|
Title: Re: RYCA take off's Post by verslagen1 on 11/18/23 at 09:38:51 I've looked at them with a camera and I can make them out. $70 to brazil for a medium box and $80 for a large, I suggest you fill them up. |
|
Title: Re: RYCA take off's Post by TheBabyDerp on 10/23/24 at 09:10:33 do you still have a factory toolkit? if so, what is included in that? |
|
Title: Re: RYCA take off's Post by verslagen1 on 10/23/24 at 14:52:27 I do believe I have 1 full kit but you'll have to wait a week to get the contents. |
|
Title: Re: RYCA take off's Post by TheBabyDerp on 10/23/24 at 17:08:27 alright |
|
Title: Re: RYCA take off's Post by verslagen1 on 10/30/24 at 10:19:27 7B676A6D6E6D766B6A7D7F0F0 wrote:
Here's what I have... Hey, this would be an interesting mod... mill the end of the 24mm wrench to fit the timing port plug. I wonder if that would work. |
|
Title: Re: RYCA take off's Post by verslagen1 on 11/06/24 at 15:33:15 I have several of these... |
|
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |