SuzukiSavage.com - Rev limiter on LS650PK2?

Donate!

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Rev limiter on LS650PK2?

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Send Topic

Print

Rev limiter on LS650PK2? (Read 8 times)

2wheelingwoman Ex Member	Rev limiter on LS650PK2? 09/26/04 at 13:58:49 Does this bike have a rev limiter?
Back to top	IP Logged

Kropatchek Serious Thumper Offline Why more than 1 cylinder? Posts: 1457 Alphen a/d Rijn Netherlands Gender:	Re: Rev limiter on LS650PK2? Reply #1 - 09/26/04 at 15:32:28 NO there's no rev. limiter on this bike. Greetz Kropatchek
Back to top	Never ask your bike to scream before her throat is warm. '93 Sav in '96 ( yellow) looks IP Logged

Savage_Greg Serious Thumper Alliance Member Offline Don't go around your ass to reach your elbow... Posts: 7844 SW Washington State Gender:	Re: Rev limiter on LS650PK2? Reply #2 - 09/27/04 at 03:00:18 You know...I've heard others say that the Savage had a rev-limiter, but I have yet to find it mentioned in the SSM either. ???
Back to top	IP Logged

klx650sm2002 Serious Thumper Offline The more I learn the less I know. Posts: 2041 Cumbria,England Gender:	Re: Rev limiter on LS650PK2? Reply #3 - 09/27/04 at 03:06:37 I read someware that it is 6500rpm, that may just be the red line though. Clive W
Back to top	IP Logged

Kropatchek Serious Thumper Offline Why more than 1 cylinder? Posts: 1457 Alphen a/d Rijn Netherlands Gender:	Re: Rev limiter on LS650PK2? Reply #4 - 09/27/04 at 03:32:42 6500 RPM sound allright. The limiting factor will be the strenght of the valvesprings. They will not close the valves anymore e.g. the valves are "floating" Greetz Kropatchek
Back to top	Never ask your bike to scream before her throat is warm. '93 Sav in '96 ( yellow) looks IP Logged

AL_DOWN_UNDER Ex Member	Re: Rev limiter on LS650PK2? Reply #5 - 09/27/04 at 23:04:25 THEY USALLY STOP REVING ONCE THE CON ROD COMES THROUGH THE CRANK CASE. SORRY CAN;T HELP MY SELF SOMETIMES
Back to top	IP Logged

Jon Ex Member	Re: Rev limiter on LS650PK2? Reply #6 - 09/28/04 at 01:10:31 Can't say I've experienced a rev limiter per se, although my previous Savages just seemed to run out of air and stop revving at ozone revs. I have seen it mentioned that the ignition clips at redline.
Back to top	IP Logged

Savage_Greg Serious Thumper Alliance Member Offline Don't go around your ass to reach your elbow... Posts: 7844 SW Washington State Gender:	Re: Rev limiter on LS650PK2? Reply #7 - 09/28/04 at 02:15:21 Maybe the rev-limiter is just inherent to the design. The low compression engine just can't get more air.
Back to top	IP Logged

klx650sm2002 Serious Thumper Offline The more I learn the less I know. Posts: 2041 Cumbria,England Gender:	Re: Rev limiter on LS650PK2? Reply #8 - 09/28/04 at 03:30:41 I've worked out the piston speed and the bottom end should be safe to 6500, can't comment on the valve springs though. Clive W
Back to top	IP Logged

Mr 650 Serious Thumper Offline The LS650- Classic style & 4-valve engine Posts: 1389 Mempho Gender:	Re: Rev limiter on LS650PK2? Reply #9 - 09/30/04 at 14:24:49 Who will be the 1st to go WOT in neutral and report if it bounces off the limiter ??? *Not me!*
Back to top	SilverBlue '01,K&N,Snorklectomy,125mm NOS carb, 1/2 spacer & 155, 'Trapp, NC flyscreen, Suzy GelSeat, Osram H4 later..putt. Putt, PUtt, PUTT! 8) HelmetLawsSuck IP Logged

AL_DOWN_UNDER Ex Member	Re: Rev limiter on LS650PK2? Reply #10 - 09/30/04 at 23:06:58 MAKE SURE YOUR CAM CHAINS IN GOOD TIGHT CONDITION OR YOU MIGHT FIND MORE THAN YOUR VALVES BOUNCING AROUND
Back to top	IP Logged

Savage_Greg Serious Thumper Alliance Member Offline Don't go around your ass to reach your elbow... Posts: 7844 SW Washington State Gender:	Re: Rev limiter on LS650PK2? Reply #11 - 10/01/04 at 02:19:14 Mr 650 wrote on 12/31/69 at 16:00:09: Who will be the 1st to go WOT in neutral and report if it bounces off the limiter ??? *Not me!* Not me either.
Back to top	IP Logged

Pages: 1

Send Topic

Print

‹ Previous topic | Next topic ›

« Home