SuzukiSavage.com - Jetting Suggestion

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Jetting Suggestion

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Jetting Suggestion (Read 4 times)

jmerry Ex Member	Jetting Suggestion 09/28/06 at 12:36:30 Can someone suggest a main and pilot jet for an 06 with an HD muffler mod, at around 2000 ft elevation? Thanks!
Back to top	IP Logged

georgekathe Ex Member	Rlar: Jetting Suggestion Reply #1 - 09/28/06 at 12:56:27 hope you get help you need, but seem to recall one response to a similar question (correctly, I guess) said every bike is a little different) & I assume what is done to white spacer will also need taking into account. george
Back to top	IP Logged

jmerry Ex Member	Re: Jetting Suggestion Reply #2 - 09/28/06 at 13:07:57 Oh yes. I've taken the white spacer down to 1/2. I'm guessing that I would need a 152.5 main and 55 pilot.. But, I'm open to suggestions of the experienced.. Also, to change these, I hope I don't have to pull the tank again! Getting the top screws out was a job! Do you just pull the bowl for the jet change? Thanks!
Back to top	IP Logged

vroom1776 Serious Thumper Offline Posts: 2110 Gender:	Re: Jetting Suggestion Reply #3 - 09/28/06 at 13:50:54 152.5 main sounds good, but the 55 pilot sounds big... what was the stock size on yrs?
Back to top	IP Logged

Guido Ex Member	Re: Jetting Suggestion Reply #4 - 09/28/06 at 14:48:17 stock on an 05 is 52.5
Back to top	IP Logged

vroom1776 Serious Thumper Offline Posts: 2110 Gender:	Re: Jetting Suggestion Reply #5 - 09/28/06 at 15:10:58 okay, 55 should be okay.... unless the PMS screw is less than 1 turn out. If the PMS screw is more than 3 turns out with the 52.5, definitley go with the 55
Back to top	IP Logged

azjay

Serious Thumper

Offline

aridzona...
its a
dry heat

Posts: 816

Gender: male

Re: Jetting Suggestion
Reply #6 - 09/29/06 at 07:02:56

jmerry wrote on 12/31/69 at 16:00:09:

I hope I don't have to pull the tank again! Getting the top screws out was a job! Do you just pull the bowl for the jet change?!

you dont need to pull the tank, but you need to remove the seat, top of the carb, throttle cable, loosen the two mounting clamps, then you can rotate the carb to get bowl screws, remove the bowl, change the jets, reassemble.

dyna muff,1/2 spacer,152.5,55,drilled air box,idle mix,spark plug door,harley bars & seat,spitfire windshield,turn signal,dunlops,man.pethingy,ISO pegs,engine cage,hiway pegs,support 81

IP Logged

jmerry Ex Member	Re: Jetting Suggestion Reply #7 - 09/29/06 at 07:17:08 Anyone know of a good vendor for these jets? I think I've seen a post somewhere..
Back to top	IP Logged

vroom1776 Serious Thumper Offline Posts: 2110 Gender:	Re: Jetting Suggestion Reply #8 - 09/29/06 at 07:19:24 local shop should have them
Back to top	IP Logged

jmerry Ex Member	Re: Jetting Suggestion Reply #9 - 09/29/06 at 07:30:08 They should.. But, I couldn't even find one that carried our oil filters.. I had to have the K&N one ordered special.
Back to top	IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home