SuzukiSavage.com - I know I've seen it here, but can't find it now.

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › I know I've seen it here, but can't find it now.

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

I know I've seen it here, but can't find it now. (Read 3 times)

Yonuh Adisi FSO

Serious Thumper

Offline

Savage Jedi (Knight)

Posts: 3622
Pilot Valley NV, aka Tatooine
Gender: male

I know I've seen it here, but can't find it now.
12/11/06 at 22:45:32

Okay, I know I had seen a thread detailing how to cut down the rear turn signals to be much closer to the fender instead of sticking out for a mile. But I can't seem to find that thread anywhere. I tried the search function and I tried searching manually (and man is there a lot of threads to search).

I would like to do this mod as my turn signals are held together with electrical tape. If I can do this mod it will save me from having to buy new signals and I thought it looked cool.

Check out Flight of Destiny http://www.amazon.com/dp/B00H9130XC

IP Logged

sluggo Serious Thumper ModSquad Offline big singles lead, twins follow the pack Posts: 4744 moses lake washington Gender:	Re: I know I've seen it here, but can't find it no Reply #1 - 12/12/06 at 08:45:44 you would be better served by replacing them with aftermarket signals, not expensive at all.
Back to top	SINGLES RULE, HARLEYS DROOL IP Logged

john1652

Ex Member

Re: I know I've seen it here, but can't find it no
Reply #2 - 12/12/06 at 12:46:10

yes replace those bulbous pigs. there are some really cool cat eye signals for the rear single element on e-bay for just a few bucks and all you need to do is drill a hole on each of fender . They look real good about an inch behind the grab bar and just below the level of the hole for the old signals. my $.02's worth anyway john

IP Logged

clueless-FSO

Senior Member

Offline

Posts: 454
Birmingham, Al
Gender: male

Re: I know I've seen it here, but can't find it no
Reply #3 - 12/12/06 at 13:06:08

I did modify mine to make them shorter. The pics don't show how I did it. Take 'em apart and throw the rubber part away. I got some hollow threaded rod, I think at the lighting section of Home Depot or Lowes along with nuts and washers. Cut to appropriate length, run wires through and fill it up with JB Weld. The JB shrinks slightly, so I used a small amount of silicon sealer where they met the fender. I have too many hobbies to feed so I do things on the cheap. Grin

I'll try to find a picture.

'96 Black "bed liner" paint.. Ed_L forward controls, HD bars with 1"socket risers, 155 main, pod filter, HD exhaust, punched baffle, modded seat, chain drive conversion, slavy mod
one of a kind

IP Logged

RadarORiley Serious Thumper Offline No one notices how you ride until you fall off. Posts: 863 West Of Weatherford, Texas Gender:	Re: I know I've seen it here, but can't find it no Reply #4 - 12/12/06 at 15:30:02 I modified mine by turning too sharp uphill in gravel. Is that the same concept? S-I-L came to the rescue & bought & installed replacement before Jr. got home so I didn't get a lecture.
Back to top	Radar O'Riley IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home