SuzukiSavage.com - Damaged Cam Lobe

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Damaged Cam Lobe

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Damaged Cam Lobe (Read 93 times)

rickj YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 18	Damaged Cam Lobe 07/09/14 at 20:07:23 Exhaust cam lobe is scoured on the peak and just beyond. Can it be repaired? It's not very deep. Rick
Back to top	IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 29042 L.A. California Gender:	Re: Damaged Cam Lobe Reply #1 - 07/09/14 at 21:40:37 is it scoured or just pitted? pitted can be ignored for awhile. if it scoured, check you oiling up there. and you can send it to webcams to get welded, maybe even pick out a new profile.
Back to top	Versey's Place Tech Section Index IP Logged

S-P Serious Thumper Offline Back in the saddle again Posts: 816 Phoenix, AZ Gender:	Re: Damaged Cam Lobe Reply #2 - 07/09/14 at 21:54:47 Maybe a picture?
Back to top	IP Logged

Dave

YaBB Moderator
ModSquad

Offline

SuzukiSavage.com
Rocks!

Posts: 18589
Camp Springs, Kentucky
Gender: male

Re: Damaged Cam Lobe
Reply #3 - 07/10/14 at 11:46:16

Yep, we need a picture. Also check the rocker, as they tend to wear the same as the cam and when one is damaged....the other most likely will be also.

If it is worn.....Webcam can weld it and make a nice Stage 1 cam for you, and they can hardweld the rockers as well.

I see in another post that you have replaced the cam chain....am I to assume that the bike is not yet completely assembled, and this is something you found while the bike is still apart?

Dave

Someday I will be old......But not today!

IP Logged

LANCER Serious Thumper Alliance Member Offline Savage Beast Performance Parts Posts: 10875 Oklahoma Gender:	Re: Damaged Cam Lobe Reply #4 - 07/10/14 at 15:06:51 Just for your info, new rockers are less costly than a hard weld on the old set. The hard weld is the better way to go if you are having the cam reground with a better profile, but new standard rockers are still ok to use. It's just what you want to do and what your budget can support.
Back to top	IP Logged

Dave YaBB Moderator ModSquad Offline SuzukiSavage.com Rocks! Posts: 18589 Camp Springs, Kentucky Gender:	Re: Damaged Cam Lobe Reply #5 - 07/10/14 at 19:19:38 Lancer. Yea...I probably wasted $ 200 getting mine hardwelded. Webcam says to get them hardwelded....so I did. I sent the rockers that only had 1,200 miles on them.....DOH! Dave
Back to top	Someday I will be old......But not today! IP Logged

LANCER

Serious Thumper
Alliance Member

Offline

Savage Beast
Performance Parts

Posts: 10875
Oklahoma
Gender: male

Re: Damaged Cam Lobe
Reply #6 - 07/10/14 at 23:13:52

Dave wrote on 07/10/14 at 19:19:38:

Lancer.

Yea...I probably wasted $ 200 getting mine hardwelded. Webcam says to get them hardwelded....so I did. I sent the rockers that only had 1,200 miles on them.....DOH!

Dave

No, not wasted, you have a better set of rockers on it now. It's a good investment if you have the $$ to work with. You can smile and talk real sweet into it's ear and remind it how much you love it. Cool

IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home