SuzukiSavage.com - Brake pad thickness

Donate!

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Brake pad thickness

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Send Topic

Print

Brake pad thickness (Read 89 times)

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28996 L.A. California Gender:	Brake pad thickness 07/28/16 at 09:54:03 I got some cheap pads that are too thick. I found 1 post that says it should be 7mm thick. Mine measure 8.5mm. Does anybody have a measurement for new pad thickness to confirm?
Back to top	Versey's Place Tech Section Index IP Logged

youzguyz Serious Thumper Offline Posts: 2557 San Antonio, Texas Gender:	Re: Brake pad thickness Reply #1 - 07/28/16 at 10:03:52 Brand new EBC FA106. 8mm entire pad (metal back + brake material)
Back to top	2002 - Silver (Thumper) 2000 - Green (Mad Hamish) Most motorcycle problems are caused by the nut between the seat and the handlebars. Make sure yours isn't too tight or too loose. IP Logged

Kenny G Serious Thumper Offline SuzukiSavage.com The Singles Club...LOL Posts: 1754 Robson Ranch, Denton, Texas Gender:	Re: Brake pad thickness Reply #2 - 07/28/16 at 10:03:55 Verslagen, I have new brake pads in the package that measure 9.38mm including the packaging and the packaging measures 1.06mm. I am guessing my pads measure measure almost 8.5mm kenny G
Back to top	IP Logged

Dave YaBB Moderator ModSquad Online SuzukiSavage.com Rocks! Posts: 18317 Camp Springs, Kentucky Gender:	Re: Brake pad thickness Reply #3 - 07/28/16 at 10:38:01 I understand that some ATV bikes use the same pad shape for the rear axle - but they do have thicker material. Have a belt sander or a Milling machine?
Back to top	Someday I will be old......But not today! IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28996 L.A. California Gender:	Re: Brake pad thickness Reply #4 - 07/28/16 at 12:19:44 I wish they'd let use the surface grinder But I took a 1mm off with big @$$ disc grinder. I'll have to check the piston to see if it's stuck.
Back to top	Versey's Place Tech Section Index IP Logged

Kenny G Serious Thumper Offline SuzukiSavage.com The Singles Club...LOL Posts: 1754 Robson Ranch, Denton, Texas Gender:	Re: Brake pad thickness Reply #5 - 07/28/16 at 13:48:48 Verslagen, Are you saying there was not enough space for the new pads to fit in the brake cylinder and then slide the cylinder back over the disk? I just looked at the reviews on the pads I purchased and there is nothing negative reported. Kenny G
Back to top	IP Logged

Kris01 Serious Thumper Offline Eat, sleep, RIDE! Posts: 3767 Tennessee Gender:	Re: Brake pad thickness Reply #6 - 07/28/16 at 19:47:03 I used the EBC FA106 pads and had no problems getting them to fit. I seem to remember someone saying another part number was too thick. Whatcha using?
Back to top	There's no problem that a full tank of gas and a sunny day can't fix! 2008 S40, Rotella T 15W-40 w/ZDDP added, Dyna, 140/90-15, Battery Tender Jr., Seat lift, #52.5/150/3 washers, Raptor IP Logged

Ruttly Serious Thumper Offline Thumpers Rule Posts: 5402 Manteca , CA Gender:	Re: Brake pad thickness Reply #7 - 07/29/16 at 10:11:22 Fleabay strikes again !
Back to top	The Topic Terminator IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28996 L.A. California Gender:	Re: Brake pad thickness Reply #8 - 07/29/16 at 11:32:37 Musta been the heat... when I finally got them in, there was plenty of clearance. Disc is just about worn out anyway.
Back to top	Versey's Place Tech Section Index IP Logged

Tocsik Serious Thumper Offline the singularity Posts: 1206 Denver, CO Gender:	Re: Brake pad thickness Reply #9 - 07/29/16 at 12:13:04 Good to hear ya got it figgerd out. Hey, what're your plans for a new disc? And how many miles are showing currently? I've seen EBC rotors supposedly for our bikes bt never investigated whether they truly have the correct mounting points.
Back to top	'08\|Raptor\|Dyna\|Stock jets & no other carb changes @ 5280' alt\|'slavy CCT\|Kawa front pulley\|130/90 rear tire\|7" LED headlight\|3" straight risers\|FIAMM El Grande horns\|Mutazu hard bags IP Logged

Pages: 1

Send Topic

Print

‹ Previous topic | Next topic ›

« Home